This component consists of reinforcement panels version 1, Non-original parts – suitable for VW T4 The curved design is intended for use in the area of the shock absorber mount on the rear axle and serves as a repair panel. The reinforcement panels are provided with a thin zinc coating. After installation, it is recommended to additionally coat the reinforcement panels, for example with a suitable primer followed by stone chip protection. Notes on the variants: There are two different versions of the reinforcement panels available. Before ordering, please check whether the stiffening of version 2 corresponds to the version shown in the product image. Version 2 with round stiffening is also available in the shop.

This component is a jack point , Non-original parts – suitable for VW T4 The jack points are intended for repair and maintenance work. Replacing both sides can be advisable, as comparable damage often occurs on the opposite side as well. The jack point is manufactured from a single piece and is made of 2 mm thick body steel sheet. The interior area is reinforced. The right-hand jack point includes the drilled holes and threads for the catalytic converter bracket. The set is intended for vehicles from model years 1990 to 2003. Reference numbers (for comparison only): 7D0 802 132 / 701 803 151

This component is a jack point , Non-original parts – suitable for VW T4 The jack points are intended for repair and maintenance work. Replacing both sides can be advisable, as comparable damage often occurs on the opposite side as well. For vehicles from model years before 1997, minor adjustments may be required on the right-hand side. The jack point is manufactured from a single piece and is made of 2 mm thick body steel sheet. The interior area is reinforced. The right-hand jack point includes the drilled holes and threads for the catalytic converter bracket. The set is intended for vehicles from model years 1997 to 2003. Reference numbers (for comparison only): 7D0 802 132 / 701 803 151

This component is a spring mount , Non-original parts – suitable for VW T4 The repair panel for the spring mount is made of 2 × 3 mm steel sheet and is intended for repair and maintenance work. The complete spring mount including the spring seat consists of a 3 mm thick bent component with a welded 3 mm base plate as well as a round component for holding the bump stop. The bump stop is included in the scope of delivery. Before ordering, please check whether the vehicle is equipped with the spring mount with two angled sides, as highlighted in blue in the last product image. Reference numbers (for comparison only): 701 803 455 C / 701 803 456 B

This component is a spring mount , Non-original parts – suitable for VW T4 . The repair panel for the spring mount is made of 2 × 3 mm steel sheet and is intended for repair and maintenance work. The complete spring mount including the spring seat consists of a 3 mm thick bent component with a welded 3 mm base plate as well as a round component for holding the bump stop. The bump stop is included in the scope of delivery. Before ordering, please check whether the vehicle is equipped with the spring mount with two angled sides, as highlighted in blue in the last product image. Reference numbers (for comparison only): 701 803 455 C / 701 803 456 B

This component is an air conditioning panel, Non-original parts – suitable for VW T4 . The component is made of 1 mm thick steel sheet and is intended for vehicles from the model years 1991 to 2003. It is located behind the luggage compartment trim on the right-hand side. The design of the air conditioning panel includes tabs that allow installation without disconnecting the air conditioning lines. Replacement is carried out as part of repair and maintenance work; fastening can be done by tack welding. Reference number (for comparison only): 7D1 801 570 A

This component is an air conditioning panel, Non-original parts – suitable for VW T4 . The component is made of 1 mm thick steel sheet and is intended for vehicles from the model years 1991 to 2003. It is located behind the luggage compartment trim on the left-hand side. The design of the air conditioning panel includes tabs that allow installation without disconnecting the air conditioning lines. Replacement is carried out as part of repair and maintenance work; fastening can be done by tack welding. Reference number (for comparison only): 7D1 801 569 A

This component is a reinforcement panel for the inner sill on the passenger side, Non-original parts – suitable for VW T4 The reinforcement panel is intended for vehicles from the model years 1997 to 2003. The design with slotted tabs allows adjustment during installation. The front corner of the panel is designed to extend beyond the edge and can be adapted to the existing profile and welded in place. Reference number (for comparison only): 701 803 766

This component is a closing panel, Non-original parts – suitable for VW T4 The component is made of 1 mm thick steel sheet and is intended for vehicles from the model years 1991–2003. It is installed in the wheel housing box on the left or right side. The closing panel separates the wheel arch liner from the step panel in the interior and features two pre-formed edges to allow adjustment during installation.After installation, it is recommended to completely seal the closing panel with a 2K primer. Afterwards, suitable stone chip protection should be applied.Reference number (for comparison only): 701801268A

This component is a closing panel, Non-original parts – suitable for VW T4 The panel is intended for installation behind the front fender on the passenger side. In this area, moisture exposure and corrosion damage can occur over time, which is why the component is replaced as part of repair and maintenance work. The closing panel is made of 1 mm thick steel sheet and is intended for vehicles from the model years 1997–2003. It features pre-formed flanges to allow adjustment during installation. Mounting is carried out at the designated attachment points.

This component is a closing panel, Non-original parts – suitable for VW T4 The panel is intended for installation behind the front fender on the driver’s side. In this area, moisture exposure and corrosion damage can occur over time, which is why the component is replaced as part of repair and maintenance work. The closing panel is made of 1 mm thick steel sheet and is intended for vehicles from the model years 1997–2003. It features pre-formed flanges to allow adjustment during installation. Mounting is carried out at the designated attachment points.

This component consists of reinforcement panels version 2, Non-original parts – suitable for VW T4 The curved design is intended for use in the area of the shock absorber mount on the rear axle and serves as a repair panel. The reinforcement panels are provided with a thin zinc coating. After installation, it is recommended to additionally coat the reinforcement panels, for example with a suitable primer followed by stone chip protection. Notes on the variants: There are two different versions of the reinforcement panels available. Before ordering, please check whether the stiffening of version 2 corresponds to the version shown in the product image. Version 1 with straight stiffening is also available in the shop.

This component is a bumper bracket repair panel, Non-original parts – suitable for VW T4 . The bumper bracket serves as a replacement part to replace a damaged or corroded bracket. The repair panel is intended for installation under the rear bumper on the driver’s side. The component is pre-bent and made of 1 mm thick steel sheet. It is intended for vehicles from the model years 1997–2003 and is suitable for repair and maintenance work. Replacing the damaged component can help restore the original mounting of the bumper. Actual fit and effectiveness may vary depending on the condition of the vehicle.

This component is a bumper bracket repair panel ,  Non-original parts – suitable for VW T4 The bumper bracket serves as a replacement part to replace a damaged or corroded bracket. The repair panel is intended for installation under the rear bumper on the passenger side The component is pre-bent and made of 1 mm thick steel sheet. It is intended for vehicles from the model years 1997–2003 and is suitable for repair and maintenance work. Replacing the damaged component can help restore the original mounting of the bumper. Actual fit and effectiveness may vary depending on the condition of the vehicle.

This component is a stabilizer bearing bracket, Non-original parts – suitable for VW T4 . The bearing bracket is installed on the rear axle (RA). It was used, among other applications, in later model variants as well as in Syncro vehicles. Reference number (for comparison only): 701 804 933 D

This component is a fuel filler neck panel, Non-original parts – suitable for VW T4 The component is made of 1 mm body steel sheet and consists of two welded parts. The design is intended for repair and maintenance work and allows the removal of the damaged area to create a suitable surface for welding. A hole for cavity wax treatment is provided.

This component is a retaining plate for the mushroom-head bolt of the seat mounting, Non-original parts – suitable for VW T4 . Reference number (for comparison only): 703 883 281B

This component consists of 2 handbrake rods with rear equalizer lever, Non-original parts – suitable for VW T4 . The set consists of pull rods and an equalizer lever and is intended for repair and maintenance work on the handbrake mechanism. Damaged or worn components of the handbrake can impair its function and are replaced as part of a repair using this set. Comparison numbers (for comparison only): 701 711 481, 721 711 475

This component is an air conditioning panel version 2, Non-original parts – suitable for VW T4 . The component is intended for repair and maintenance work and has been adapted to the structural conditions. Details and features: • Material: galvanized steel sheet, 1 mm thick • Pressing reproduced to stabilize the pipe feed-through for air conditioning lines • Mounting: M6 thread, welded, with additional spacing for line eyelets • M5 thread on the opposite side, also welded • Edge formed to match the side inner wall according to the intended installation position Actual fit may vary depending on the condition of the vehicle.

This component is the forced ventilation panel, Non-original parts – suitable for VW T4 The component is made of 1.5 mm galvanized steel sheet and is designed in the form of a repair panel. Relevant cut-outs and mounting holes for the bumper attachment are provided. The forced ventilation panel is intended for use in repair and maintenance work. Available for: left and right side Material: 1.5 mm galvanized steel sheet Comparison number (for comparison only): 701 809 171 D

This component is the forced ventilation panel, Non-original parts – suitable for VW T4 The component is made of 1.5 mm galvanized steel sheet and is designed in the form of a repair panel. Relevant cut-outs and mounting holes for the bumper attachment are provided. The forced ventilation panel is intended for use in repair and maintenance work. Available for: left and right side Material: 1.5 mm galvanized steel sheet Comparison number (for comparison only): 701 809 171 D

This component is a cross member above the spare wheel, Non-original parts – suitable for VW T4 The component is made of automotive steel with a material thickness of 1.5 mm. The cross member is located centrally above the spare wheel. In this area, corrosion damage can occur over time, which is why the cross member is often replaced as part of repair and maintenance work. Comparison number (for comparison only): 7D1 803 533 B

This component is the longitudinal member Non-original parts – suitable for VW T4 The longitudinal member for the rear section of the vehicle is made of 3 mm thick steel sheet. It covers the rear area from the C-pillar to the D-pillar. Holes, cut-outs, and angles are designed according to the intended installation position and are intended for repair and maintenance work. Comparison numbers (for comparison only): 7D0 804 465 / 7D0 804 466

This component is the longitudinal member Non-original parts – suitable for VW T4 The longitudinal member for the rear section of the vehicle is made of 3 mm thick steel sheet. It covers the rear area from the C-pillar to the D-pillar. Holes, cut-outs, and angles are designed according to the intended installation position and are intended for repair and maintenance work. Comparison numbers (for comparison only): 7D0 804 465 / 7D0 804 466

The shock absorber mount serves as the attachment point for the shock absorber on the rear axle and is a component for the suspension function. With this product, you can repair your vehicle and ensure the proper functioning of the rear axle suspension.Note:It is recommended to replace the shock absorber mount at the same time as replacing the spring mount.Reference number: 7D0803545

The shock absorber mount serves as the attachment point for the shock absorber on the rear axle and is a component for the suspension function. With this product, you can repair your vehicle and ensure the proper functioning of the rear axle suspension.Note:It is recommended to replace the shock absorber mount at the same time as replacing the spring mount.Reference number: 7D0803546

The Offroadgrip roof rack is a modular mounting system for the installation of cargo and accessories on vehicle roofs. This version is suitable for airline rails with a hole spacing of 25.4 mm and is designed for applications in off-road, campervan, and motorhome environments.The system is made of stainless steel and allows the flexible integration of various attachments, such as solar panels, lights, awnings, roof tents, or sun sails. In combination with suitable adapters, aluminum system profiles up to 40 × 40 mm can also be connected.This system offers a wide range of expansion options within the Offroadgrip modular system.Scope of delivery: Roof rack including mounting components (L-bracket, slot nut plate, screws and nuts made of stainless steel).

This product consists of fenders, not original parts – suitable for VW T4. These are available as 15-inch and 16-inch variants. The fenders are made of GRP (glass fiber reinforced plastic) and serve as a replacement or retrofit solution within the scope of bodywork. The components are delivered primed and are intended for further processing (painting). Manufacturing takes place in Germany by an experienced producer who has been producing products for road and motorsport use for many years. If you have any questions about the product or the available variants, please do not hesitate to contact us.

Product description: The molded covers serve as a cover for the rear side windows. They are made of GFRP glass fiber reinforced plastic (epoxy resin). Installation note: Attachment is carried out by bonding with suitable window adhesive to glass or sheet metal. The adhesive is not included in the scope of delivery. Installation must be carried out properly by qualified personnel to ensure safe and permanent attachment. Fitment: Suitable for vehicles with a short wheelbase of 2920 mm.

This component is a cross member behind the spare wheel, Non-original parts – suitable for VW T4 . The cross member is located in the direction of travel in front of the spare wheel and serves to support the spare wheel carrier. The cross member is made of 2 mm thick steel sheet and is intended for repair and maintenance work. The mounting tabs are designed without pre-drilled holes, allowing new welding points to be set. Comparison part number (for comparison only): 701 803 537 A

This component is an acoustic capsule, Non-original parts – suitable for VW T4 . The design is intended for use in the area of the gear linkage. The capsule forms a stable outer shell. The interior can optionally be lined with suitable sound insulation materials to further support noise reduction (insulation material not included). The additional cover can help reduce the transmission of noise from the area of the engine tunnel. It may also help reduce heat transfer into the interior. Scope of delivery: • 1 × foam rubber strip, approx. 650 mm, for sealing the contact surfaces Reference part number (for comparison only): 7D0 711 545 / 7D0711545

This component is a repair kit for the balance bar, Non-original parts – suitable for VW T4 . This kit serves as a replacement if components of the balance bar are damaged or worn. The repair kit consists of coordinated components and is intended for use in repair and maintenance work. 

It is a holder for the ABS cable Non-original parts – suitable for VW T4 . If the holder is damaged or missing, the routing of the ABS cable may be impaired. This component serves as a replacement part for repair and maintenance work and is intended for vehicles compatible with VW T4.

This component is a sliding door spacer wedge Non-original parts – suitable for VW T4 . The sliding door wedge is used to move the position of the sliding door 20 mm outward. It is often used in conjunction with modified wheel or tire combinations when contact or restricted movement may occur in the area of the sliding door. The component is intended for use in repair and adjustment work and can help increase the distance between the sliding door and the body. The actual effect may vary depending on vehicle condition, wheel, and tire combination. Part number: 104-11-280-15 If you have any questions about the product or its application, please feel free to contact us.

This item is a valve cover bolt seal, Non-original parts – suitable for VW T4 . Leaks in the area of the valve cover bolt can occur especially in older engines and may be associated with oil loss. This seal serves as a replacement part if the existing seal has become brittle or damaged. The seal is designed for its intended application and is manufactured from oil- and temperature-resistant material. Replacement is possible with basic mechanical skills. According to feedback from practical use, replacing a defective seal can help reduce oil loss. However, the actual effect may vary depending on vehicle condition and installation situation. Compatible with engine codes: ACV, AHY, AXG, AXL, AJT, AYC, AUF, AYY Part numbers (for comparison only): 074 103 469 P / 074 103 469 F

This product is a 4-piece holder set, Non-original parts – suitable for VW T4 . Over the years, original holders can become damaged or break due to aging or material fatigue. This set serves as a replacement solution to repair or replace the corresponding holders. The parts are manufactured to fit precisely and are intended for use in repair and maintenance work. Installation is possible with basic mechanical skills. Actual fit and function may vary depending on the condition of the vehicle. Reference number: 037133567F If you have any questions about the product or its application, please feel free to contact us.