1 pair of reinforcement plates rear shock absorbers version 2 curved Non-original parts – suitable for VW T4
- Personalised advice on the product
- designed specifically for the relevant vehicle model
- high-quality materials
- intended for repair and maintenance work
€79.00
Available, delivery time: 3-5 Tage international delivery time 5-7 days
Product information "1 pair of reinforcement plates rear shock absorbers version 2 curved Non-original parts – suitable for VW T4"
This component consists of reinforcement panels version 2, Non-original parts – suitable for VW T4
The curved design is intended for use in the area of the shock absorber mount on the rear axle and serves as a repair panel. The reinforcement panels are provided with a thin zinc coating.
After installation, it is recommended to additionally coat the reinforcement panels, for example with a suitable primer followed by stone chip protection.
Notes on the variants:
There are two different versions of the reinforcement panels available. Before ordering, please check whether the stiffening of version 2 corresponds to the version shown in the product image.
Version 1 with straight stiffening is also available in the shop.
| Category: | Weld-in repair panel |
|---|---|
| Coating: | Electro-galvanized coating |
| Orientation: | rear |
| Year of construction: | 1991-2003 |
| installation side: | left, right |
| suitable for: | VW T4 |
Manufacturer Information
Delta Garage UG (limited liability)
Pfaffenhofener Str. 3A
85302 Gerolsbach
Germany
Phone, WhatsApp, Telegram:
0160 94663915
Email:
service@deltagarage.de
Contact form:
ticket.deltagarage.de
Installation must be carried out by qualified personnel
Product may have sharp edges – wear protective gloves
Use only for the intended vehicle type
Login
The use of our repair panels and spare parts requires proper installation. We recommend installation by a qualified workshop. We accept no liability for incorrect installation or any resulting damage.
Diese Bleche sind meist auch betroffen
This component is an air conditioning panel, Non-original parts – suitable for VW T4 . The component is made of 1 mm thick steel sheet and is intended for vehicles from the model years 1991 to 2003. It is located behind the luggage compartment trim on the left-hand side. The design of the air conditioning panel includes tabs that allow installation without disconnecting the air conditioning lines. Replacement is carried out as part of repair and maintenance work; fastening can be done by tack welding. Reference number (for comparison only): 7D1 801 569 A
This component is an air conditioning panel, Non-original parts – suitable for VW T4 . The component is made of 1 mm thick steel sheet and is intended for vehicles from the model years 1991 to 2003. It is located behind the luggage compartment trim on the right-hand side. The design of the air conditioning panel includes tabs that allow installation without disconnecting the air conditioning lines. Replacement is carried out as part of repair and maintenance work; fastening can be done by tack welding. Reference number (for comparison only): 7D1 801 570 A
This component is an air conditioning panel version 2, Non-original parts – suitable for VW T4 . The component is intended for repair and maintenance work and has been adapted to the structural conditions. Details and features: • Material: galvanized steel sheet, 1 mm thick • Pressing reproduced to stabilize the pipe feed-through for air conditioning lines • Mounting: M6 thread, welded, with additional spacing for line eyelets • M5 thread on the opposite side, also welded • Edge formed to match the side inner wall according to the intended installation position Actual fit may vary depending on the condition of the vehicle.
This component is the forced ventilation panel, Non-original parts – suitable for VW T4 The component is made of 1.5 mm galvanized steel sheet and is designed in the form of a repair panel. Relevant cut-outs and mounting holes for the bumper attachment are provided. The forced ventilation panel is intended for use in repair and maintenance work. Available for: left and right side Material: 1.5 mm galvanized steel sheet Comparison number (for comparison only): 701 809 171 D
This component is the forced ventilation panel, Non-original parts – suitable for VW T4 The component is made of 1.5 mm galvanized steel sheet and is designed in the form of a repair panel. Relevant cut-outs and mounting holes for the bumper attachment are provided. The forced ventilation panel is intended for use in repair and maintenance work. Available for: left and right side Material: 1.5 mm galvanized steel sheet Comparison number (for comparison only): 701 809 171 D
This component is a spring mount , Non-original parts – suitable for VW T4 The repair panel for the spring mount is made of 2 × 3 mm steel sheet and is intended for repair and maintenance work. The complete spring mount including the spring seat consists of a 3 mm thick bent component with a welded 3 mm base plate as well as a round component for holding the bump stop. The bump stop is included in the scope of delivery. Before ordering, please check whether the vehicle is equipped with the spring mount with two angled sides, as highlighted in blue in the last product image. Reference numbers (for comparison only): 701 803 455 C / 701 803 456 B
This component is a spring mount , Non-original parts – suitable for VW T4 . The repair panel for the spring mount is made of 2 × 3 mm steel sheet and is intended for repair and maintenance work. The complete spring mount including the spring seat consists of a 3 mm thick bent component with a welded 3 mm base plate as well as a round component for holding the bump stop. The bump stop is included in the scope of delivery. Before ordering, please check whether the vehicle is equipped with the spring mount with two angled sides, as highlighted in blue in the last product image. Reference numbers (for comparison only): 701 803 455 C / 701 803 456 B