VW T4 air conditioning panel rear right V2 no original

Product information ‘VW T4 air conditioning panel rear right - replica’ The replica of the VW T4 air conditioning panel is the ideal solution as a repair panel if the old panel on your vehicle has rusted through. It is made of 1 mm sheet steel and is suitable for vehicles built between 1991 and 2003. The VW T4 air conditioning panel is located behind the boot panelling on the right-hand side. The design of the air conditioning panel has a predetermined breaking point with tabs, which means that the two air conditioning lines do not have to be separated. This means you can replace the air conditioning panel quickly and easily. The panel is fitted with just a few staples. Notes on fitting the VW T4 air conditioning panel To ensure that the VW T4 air conditioning panel can be fitted quickly and easily, you should speak to a technician from a certified testing centre (e.g. TÜV, DEKRA, etc.) in advance. Installation should only be carried out by professionally trained personnel (e.g. master body shop) to ensure safe and correct installation. After installation, you should completely seal the air conditioning panel with a 2K primer. Afterwards, a proper stone chip protection should be applied. Reliable and durable air conditioning panel for your VW T4 If you need a reliable and durable air conditioning panel for your VW T4, this is the perfect choice. It is an ideal solution for those who need to replace a faulty air conditioning panel without investing a lot of time or money. You can use the reference number 7D1801570A to easily identify and order the right air conditioning panel for your vehicle.

Product information "VW T4 forced ventilation, rear bumper mount, repair panel left"Product information VW T4 forced ventilation, bumper mount, repair sheetIf your VW T4 is affected by rust - especially in the area of ​​the rear forced ventilation - we have the ideal solution for you: a special repair sheet that is precisely tailored to the needs of welding. Made from solid 1.5 mm galvanized sheet steel and based on the original VW repair sheet Developed by us, this sheet offers a durable and robust solution for protecting the affected area. All necessary recesses and holes for the bumper attachment are already present, which enables a precise and uncomplicated installation. A special advantage: The sheet is designed in such a way that a generous removal of the rusted area is easily possible. So if not only the forced ventilation but also the rear side wall of your T4 above the bumper is affected by rust, this area can also be reliably covered with the repair sheet. With this repair panel, your VW T4 gets a well thought-out and durable solution that gives it a new shine and keeps rust at bay in the long term. Available for left and right side in 1, 5 mm galvanized sheet steel.Reference number 701809171D

Product information "VW T4 forced ventilation, rear bumper mount, repair panel right"Product information VW T4 forced ventilation, bumper mount, repair sheetIf your VW T4 is affected by rust - especially in the area of ​​the rear forced ventilation - we have the ideal solution for you: a special repair sheet that is precisely tailored to the needs of welding. Made from solid 1.5 mm galvanized sheet steel and based on the original VW repair sheet Developed by us, this sheet offers a durable and robust solution for protecting the affected area. All necessary recesses and holes for the bumper attachment are already present, which enables a precise and uncomplicated installation. A special advantage: The sheet is designed in such a way that a generous removal of the rusted area is easily possible. So if not only the forced ventilation but also the rear side wall of your T4 above the bumper is affected by rust, this area can also be reliably covered with the repair sheet. With this repair panel, your VW T4 gets a well thought-out and durable solution that gives it a new shine and keeps rust at bay in the long term. Available for left and right side in 1, 5 mm galvanized sheet steel.Reference number 701809171D

Product information ‘VW T4 spring retainer spring plate right - replica’ Discover the perfect replacement part for the rear right shock absorber of your VW T4 with the replica of the VW T4 upper spring mount - spring plate. The repair plate for the VW T4 spring mount is made from high-quality 2x3 mm sheet steel to guarantee a stable and durable solution. The complete spring mount incl. spring disc consists of a robust 3 mm edged part with a welded 3 mm base plate and a round part for the buffer mount. The impact buffer is also included in the scope of delivery. Powder-coated for optimum protection Thanks to the high-quality powder coating, the repair plate is optimally protected against rust and guarantees a long service life. You don't even have to worry about the areas to be welded. The coating can be removed a little and the sheet metal can then be preserved again. In addition, the spring mount should be sealed with a 2K primer at the welding points after installation. A cavity sealant should also be applied to the interior. Notes on the VW T4 upper spring mount - right-hand spring plate Please note that any adjustments may have to be made to your vehicle during installation. Before ordering, you should also check on your VW T4 whether your spring mount is the version with two sloping sides, as highlighted in blue in the fourth product image. To ensure that the VW T4 spring mount can be installed quickly and easily, you should speak to a technician from a certified testing centre (e.g. TÜV, DEKRA, etc.) in advance. Installation should only be carried out by professionally trained personnel (e.g. a master body shop) to ensure safe and correct installation. Get your VW T4 back on the road All in all, our repair plate offers a reliable and effective solution for VW T4 spring mounts and guarantees a long service life. With the reference number 701803456B, you can easily identify the right spring mount for your vehicle. Order it now and get your vehicle back on the road!

Product information ‘VW T4 spring retainer spring plate left - replica’ Discover the perfect replacement part for the rear right shock absorber of your VW T4 with the replica of the VW T4 upper spring mount - spring plate. The repair plate for the VW T4 spring mount is made from high-quality 2x3 mm sheet steel to guarantee a stable and durable solution. The complete spring mount incl. spring disc consists of a robust 3 mm edged part with a welded 3 mm base plate and a round part for the buffer mount. The impact buffer is also included in the scope of delivery. Powder-coated for optimum protection Thanks to the high-quality powder coating, the repair plate is optimally protected against rust and guarantees a long service life. You don't even have to worry about the areas to be welded. The coating can be removed a little and the sheet metal can then be preserved again. In addition, the spring mount should be sealed with a 2K primer at the welding points after installation. A cavity sealant should also be applied to the interior. Notes on the VW T4 upper spring mount - left-hand spring plate Please note that any adjustments may have to be made to your vehicle during installation. Before ordering, you should also check on your VW T4 whether your spring mount is the version with two sloping sides, as highlighted in blue in the fourth product image. To ensure that the VW T4 spring mount can be installed quickly and easily, you should speak to a technician from a certified testing centre (e.g. TÜV, DEKRA, etc.) in advance. Installation should only be carried out by professionally trained personnel (e.g. a master body shop) to ensure safe and correct installation. Get your VW T4 back on the road All in all, our repair plate offers a reliable and effective solution for VW T4 spring mounts and guarantees a long service life. With the reference number 701803456B, you can easily identify the right spring mount for your vehicle. Order it now and get your vehicle back on the road!

Product information ‘VW T4 bumper bracket repair plate for right rear axle’ The bumper bracket as a repair plate is the ideal solution for replacing a damaged or outdated bracket on your VW T4. This replica was specially designed for the VW T4 and is located under the rear bumper on the driver's side of your vehicle. The repair plate is pre-folded and made of robust 1 mm sheet steel. The bumper bracket is suitable for vehicles built between 1997 and 2003 and fits perfectly into the frame of your VW T4. By replacing the defective or damaged original part with the bumper bracket as a repair plate, you can easily restore stability and safety. Instructions for fitting the VW T4 bumper bracket repair plate To ensure that the VW T4 bumper bracket repair plate can be fitted quickly and easily, you should speak to a technician from a certified testing centre (e.g. TÜV, DEKRA, etc.) in advance. The installation should only be carried out by professionally trained personnel (e.g. master body shop) to ensure safe and correct installation. You should then seal the bumper bracket completely with a 2K primer. Bumper bracket replica for the VW T4: Simple and effective solution The bumper bracket replica as a repair panel is a practical and uncomplicated solution for every VW T4 owner who needs this important repair panel and whose vehicle is to remain in optimum condition for many years.

Product information ‘VW T4 bumper bracket repair plate for left rear axle’ The bumper bracket as a repair plate is the ideal solution for replacing a damaged or outdated bracket on your VW T4. This replica was specially designed for the VW T4 and is located under the rear bumper on the driver's side of your vehicle. The repair plate is pre-folded and made of robust 1 mm sheet steel. The bumper bracket is suitable for vehicles built between 1997 and 2003 and fits perfectly into the frame of your VW T4. By replacing the defective or damaged original part with the bumper bracket as a repair plate, you can easily restore stability and safety. Instructions for fitting the VW T4 bumper bracket repair plate To ensure that the VW T4 bumper bracket repair plate can be fitted quickly and easily, you should speak to a technician from a certified testing centre (e.g. TÜV, DEKRA, etc.) in advance. The installation should only be carried out by professionally trained personnel (e.g. master body shop) to ensure safe and correct installation. You should then seal the bumper bracket completely with a 2K primer. Bumper bracket replica for the VW T4: Simple and effective solution The bumper bracket replica as a repair panel is a practical and uncomplicated solution for every VW T4 owner who needs this important repair panel and whose vehicle is to remain in optimum condition for many years.

Produktinformationen "VW T4 Querträger über Reserverad - Nachbau"VW T4 Querträger über Reserverad - Nachbau"Der VW T4 Querträger über Reserverad ist dem Original VW Reparaturblech nachempfunden und absolut passgenau gefertigt. Das Material ist Fahrzeugstahl mit einer Stärke von 1,5 mm, somit etwas fester als das Original mit 1,3 mm. Der VW T4 Querträger über Reserverad befindet sich, wie der Name es bereits andeutet, genau in der Mitte über dem Reserverad, was den Träger oft sehr zu schaffen mach und dieser nahezu bei allen VW T4 durchgerostet ist.  VAG-Vergleichsnummer, Teilenummer: 7D1803533 B

Product information ‘VW T4 strike plate for cross member - reproduction The replica is very detailed and contains all the necessary cut-outs for clean welding of the VW T4 striker plate for cross members. The repair plate is 2 mm thick and galvanised. Attention: The repair plate will be shipped as spear material. Reference number: 70180

Product information ‘VW T4 reinforcement plates shock absorber version 2 (curved) for rear left + right’ The VW T4 replica reinforcement plates version 2 (curved) for the shock absorber mount on the rear axle are the perfect repair plates if your vehicle suffers from rust damage at this important point. The replica of the reinforcement plates is made from 2 mm sheet steel. They can be welded easily and securely, ensuring a perfect connection to the vehicle frame. Galvanised The VW T4 reinforcement plates are coated with a wafer-thin layer of zinc, providing ideal protection against rust and damage. After installation, you should completely seal the reinforcement plates with a 2K primer. Afterwards, a proper stone chip protection should be applied. Notes on rebuilding the VW T4 reinforcement plates - curved Please note that there is a ‘curved’ version 2 with curves when reproducing the reinforcement plates. Before ordering, you should check on your VW T4 whether the reinforcement on the reinforcement plate is as shown in the picture. Version 1 with ‘straight’ reinforcement is also available here in the shop. To ensure that the VW T4 reinforcement plates can be fitted quickly and easily, you should speak to a technician from a certified testing centre (e.g. TÜV, DEKRA, etc.) in advance. The installation should only be carried out by professionally trained personnel (e.g. master body shop) to ensure safe and correct installation. Stabilise your VW T4 on the rear axle If the old reinforcement plates have rusted through, you can simply replace them with our reinforcement plates to give your vehicle more stability and longevity.

Product information ‘VW T4 1 pair of rear shock absorber reinforcement plates as a set left and right version 1 (straight)’ The VW T4 replica reinforcement plates version 1 (straight) for the shock absorber mount on the rear axle are the perfect repair plates if your vehicle suffers from rust damage at this important point. The replica of the reinforcement plates is made from 2 mm sheet metal and is significantly stronger than the original. They can be welded easily and securely, ensuring a perfect connection to the vehicle frame. Galvanised The VW T4 reinforcement plates are coated with a wafer-thin layer of zinc, providing ideal protection against rust and damage. After installation, you should completely seal the reinforcement plates with a 2K primer. Afterwards, a proper stone chip protection should be applied. Notes on rebuilding the VW T4 reinforcement plates - straight Please note that there is a ‘straight’ version 1 without curves when reproducing the reinforcement plates. Before ordering, you should check on your VW T4 whether the reinforcement on the reinforcement plate is as shown in the picture. Version 2 with ‘curved’ reinforcement is also available here in the shop. To ensure that the VW T4 reinforcement plates can be fitted quickly and easily, you should speak to a technician from a certified testing centre (e.g. TÜV, DEKRA, etc.) in advance. The installation should only be carried out by professionally trained personnel (e.g. master body shop) to ensure safe and correct installation. Stabilise your VW T4 on the rear axle If the old reinforcement plates have rusted through, you can simply replace them with our reinforcement plates to give your vehicle more stability and longevity.